RTL-SDR Blog V.3. Dongles User Guide

RTL-SDR Blog V3 Counterfeit Warning!

If you have purchased a counterfeit RTL-SDR Blog V3 device the features described in this guide may not work correctly, if at all. If you were tricked into thinking it was an original RTL-SDR Blog V3, please lodge a dispute with the marketplace platform purchased from. 

Please purchase either directly from our store, or using the links on the store to official marketplace listings or resellers.

Version 3 of our customized RTL-SDR dongles brought out some new interesting features. In this guide we explain how to use those feature. If you are interested, we also have the V3 feature datasheet available here.

Feature 1: Direct Sampling HF Mode

This feature allows you to listen to HF signals between about 500 kHz to 28.8 MHz.

To use direct sampling mode

1. Connect an appropriate HF antenna to the SMA antenna port (this is the same port where you connect your VHF/UHF antenna). 
2. In SDR# select the Q-branch in the configure menu (the cog icon next to the play button). (If it is greyed out make sure you stop the SDR first, by clicking the stop button in SDR#)
3. Press Play and tune to 500 kHz – 28.8 MHz.

VHF antennas like small discones or short whip antennas will probably not pick up HF signals very well, if at all. If you have one of our dipole antennas, try connecting a long 5 meter or longer wire to the element connected to the coax center wire. To check which element is connected to the center coax you can open the lid on the black dipole base. Ideally you should use a 9:1 unun with the long wire antenna for optimal reception. Even more ideally you’d use an antenna tuner, though this is expensive.

HDSDR/GQRX and Other Software

Other software like HDSDR and GQRX can also support direct sampling. It may entail setting a device string, and for the Q-branch, the value should be 2 (or sometimes 3). In GQRX the device string would be “rtl=0,direct_samp=2” (without the quotes). In some installs that use different drivers it may be “rtl=0,direct_samp=3” instead. Make sure that there is no space after the comma. For SDR-Console please see this linked post for a modified ExtIO that can enable direct sampling. SDR-Touch on Android has a direct sampling option available in its settings page.

To go back to listening to frequencies above 28.8 MHz remember to change the sampling mode back to “Quadrature Sampling”.

Note that this feature makes use of direct sampling and so aliasing will occur. The RTL-SDR ADC samples at 28.8 MHz, thus you may see mirrors of strong signals from 0 – 14.4 MHz while tuning to 14.4 – 28.8 MHz and the other way around as well. To remove these images you need to use a low pass filter for 0 – 14.4 MHz, and a high pass filter for 14.4 – 28.8 MHz, or simply filter your band of interest. (Note that that 28.8 MHz is downsampled on chip resulting in the 3.2 MHz bandwidth)

Modified rtl_tcp for direct sampling

The standard Osmocom version of rtl_tcp only allows for direct sampling on the I-branch, which is useless as we need direct sampling on the Q-branch. Please see our RTL-SDR-Blog Drivers for a version that includes a -D direct sampling flag. The Releases page has a Windows release.

Forcing Direct Sampling To be Always ON

In some cases you may want to force direct sampling to be always on. For example, not all programs expose the direct sampling controls to the user, so in those programs it can be impossible to turn direct sampling mode on. To force it on, use our RTL-SDR-Blog driver branch, and use set the direct sampling always on flag in the EEPROM with the command “rtl_eeprom -q y”. To disable forced direct sampling do the opposite command “rtl_eeprom -q n”

Feature 2: Software Selectable Bias Tee

V.1. and V.2. of our dongles included a bias tee which could manually be enabled by opening the case and soldering two pads on the PCB together. V.3. introduces a 4.5V bias tee that can be toggled entirely in software. The bias tee can continuously pull up to 180 mA of current.

WARNING: Before using the bias tee please ensure that you understand that you should not use this option when the dongle is connected directly to a DC short circuited antenna unless you are using an LNA. Although the bias tee circuit is dual protected against accidental shorts with a thermal self-resetting fuse and overcurrent protection on the LDO, short circuiting the bias tee for an extended period of time (days) could damage the LDO or fuse permanently. Only use it while connected to an actual powered device, like an LNA, active antenna or the SpyVerter.

To make things clearer: DC Short Antenna -> LNA -> Coax -> V3(bias tee on) is absolutely fine. What’s not good and makes no sense anyway is DC Short Antenna -> Coax -> V3(bias tee on). DC Short Antenna -> Coax -> V3(bias tee off) is fine.

Note that the legacy DVB-T TV drivers will activate the bias tee by default. On Linux ensure that you have properly blacklisted the DVB-T drivers. More info on how to blacklist on the Linux section on the quickstart guide.

Optional Video: Bias tee tutorial by SignalsEverywhere available here.

To enable the bias tee in Windows:

1. Download and extract all the files in this zip file to a folder on your PC. It contains two batch files that can be run.
2. Make sure all SDR software like SDR#/HDSDR/SDR-Console etc is fully closed.
3. Run the biastee_on.bat file to turn the bias tee on. It will run and open a CMD prompt that will briefly say “Found Rafael Micro R820T Tuner”. The CMD prompt will close soon after upon success.
4. The bias tee is now on. To turn it off repeat steps 2 & 3, but instead run the biastee_off.bat batch file. Alternatively, simply disconnect and then reconnect the SDR to turn the bias tee off.

If you have multiple dongles connected you’ll need to edit the batch file to specify what dongle’s bias tee you want to activate. Open the bat file with any text editor, like Notepad, and add the dongle selector “-d” flag. For example to activate the bias tee on the dongle that was plugged in second you’d need to change it to “rtl_biast -b 1 -d 1”.

If you get a Smart Screen message, click on More Info, and then on Run Anyway. Also note that some versions of Windows may fail to run batch files due to misconfiguration or aggressive antivirus software. If you cannot fix these problems with Windows or your antivirus, run the command manually on the CMD line.

To run it manually on the CMD line first browse to the directory where the bias tee software is stored using “cd” (e.g. cd C:\SDR\bias_tee_folder), and then run:

1. ON: rtl_biast -b 1
2. OFF: rtl_biast -b 0
3. If needed select a particular RTL-SDR device with the -d flag.

To enable the bias tee in Linux:

In Linux or MacOS download the source from git, compile it the same way you do the regular RTL-SDR drivers, and then run ./rtl_biast -b 1 to turn the bias tee on and ./rtl_biast -b 0 to turn the bias tee off. The procedure is:

git clone https://github.com/rtlsdrblog/rtl-sdr-blog
cd rtl-sdr-blog
mkdir build
cd build
cmake .. -DDETACH_KERNEL_DRIVER=ON
make
cd src
./rtl_biast -b 1

If you want to be able to run the bias tee program from anywhere on the command line you can also run “sudo make install”.

If you have trouble running the bias tee check with a multimeter if there is 4.5V at the SMA port. Also check that your powered device is actually capable of receiving power. Remember that not all LNA’s can accept bias tee power. We recommend Adam 9A4QV’s LNA4ALL, as you can order this from his store with the bias tee power option enabled. If you need further help please contact us at [email protected]

Enabling the Bias Tee in PiAware

Please see this link for instructions, or see below to see how to force the bias tee to be always on.

Forcing the Bias Tee to be Always On

If you are using our RTL-SDR-Blog driver branch you can force the bias tee to be always on by setting a flag in the EEPROM. The rtl_eeprom command is “rtl_eeprom -b y”. Run the opposite command “rtl_eeprom -b n” to disable the forced bias tee.

Feature 3: Selectable Clock & Expansion Headers

This is for advanced users who need to daisy chain clocks together for coherent experiments, or need to access other ports. You can either bridge the clock selector the directly with a solder bridge, or solder on a 1.27mm 2×2 header pin jumper.

To add a jumper to the CLK selector header.

1. Carefully remove the 0 Ohm resistor.
2. Very carefully solder a 1.27mm 2×2 header onto the clock selector pads.
3. You can now select your clock input.

How to connect the CLK jumpers:

 The first position allows you to output the dongles clock to the CLK pads. The second position allows you to input an external clock.

An example of CLK daisy chaining is shown below. One dongles TCXO is connected to two other dongles who have disconnected clocks.

Feature 4: Additional GPIO Ports

Please see the guide written by Rodrigo Freire here.

LF/MF Improvement / Bias Tee Disable Mod:

If you want to improve the performance at LF/MF (below 500 kHz) and do not require the bias tee, then you can remove the bias tee inductor at L13. Of course remember that if you are interested in VLF/LF, it might be a better idea to use an upconverter like the SpyVerter, which can be powered by the bias tee on the dongle.

Notes to be aware of:

I opened my RTL-SDR V3 dongle and found that the thermal pad has a small air gap between it and the enclosure, is this normal?

This is normal. The purpose of the thermal pad is to fix L-band VCO lock problem that are related to PCB heat build up. The RTL-SDR V3 only requires very minor heat sinking to overcome this issue, and a small air gap does not reduce the thermal transfer enough to cause issues. In fact the V3 PCB has already been redesigned to dissipate heat better, so the thermal pad is not strictly required, except in very warm climates.

My RTL-SDR V3 is getting hot.

Please remember that these units do get hot to the touch especially when used in warm climates. This is not an issue and is normal. The temperature will normally be about 20 – 25C above ambient. We have improved the thermal bonding and heat transfer between the chips and the metal case. This results in making the metal case hotter, but it keeps the chips much cooler, resulting in better performance. To lengthen the life of the dongle we recommend keeping the unit away from direct hot sunlight.

Current Known Issues:

We’re constantly trying to improve our units and we always make note of what issues exist and how to fix them.

2019 Onwards:

No known issues.

2019 and earlier units (no longer shipping):

Note that the following problem has been fixed in newer batches with a new design.

0.2 – 0.3% of units may have a faulty RTL2832U chip. This is characterized by higher than normal USB currents (normal is 0.28A – 0.3A), and often random disconnections from the USB as well as increased heat. The same problem affects all brands of RTL-SDR.

2018/8 Batch (no longer shipping):

A small number of these units (~approx 300 units) had faulty bias tee LDO chips which caused the bias tee to be permanently on. The cause was bad silicon in the LDO chip. These units run normally in all other ways, except that the bias tee cannot be turned off. They can continue to be used normally, without the bias tee. The thermal fuse will protect against short circuits.

If you have one of these, feel free to contact us at [email protected] for a replacement, or if the bias tee is not important to you and you can solder, removing the L13 inductor will fully disable the bias tee.  

Known V3 Batch 1 Issues (limited quantity batch, no longer shipping):

1. Increased sideband noise on very strong narrowband signals. This should not be a significant problem as it only affects very strong signals. The hardware fix is to add about 100-220uF of capacitance on the 3.3V power line. Batch 2 will reduce this noise.
2. The bias tee when turned on adds a large spur in direct sampling HF mode. This may be problematic only if you intend to use a bias tee powered HF LNA in direct sampling mode. This can be fixed by adding about 2.2uF of capacitance to the output of the LDO, before the inductor. Batch 2 will fix this.
3. The bias tee can be damaged by accidentally short circuiting the output for a few seconds while it is on. This damage only occurs on USB3.0 and USB2.0 ports that can provide up to 1A or more or current. Batch 2 will add a resettable fuse to prevent damage.

Reddit

Vote

Email

103

Shares